MSP 430 based Low Frequency Oscilloscope

A crucial equipment for any electronics enthusiast besides multimeter,soldering iron,etc is an Oscilloscope. Unfortunately these oscilloscopes come at a price which students or hobbyists couldn't afford.

Here, a low frequency oscilloscope is designed using TI's MSP430G2231 microcontroller. The frequency range it could measure is few Khz but that is sufficient for most circuits testing since they operate on low frequencies.

Components used:

MSP430G2231 microcontroller
MSP430 Launchpad
3.3V Voltage regulator *
USB-Serial Converter *
BC547 transistors *
Switches *
LEDS *
Connectors,General Purpose board,wires,etc *

* - Optional

I have made the entire circuit in a stand-alone pcb here. This can be very well implemented with Launchpad alone since it has everything onboard.The overall block diagram is given below.

The input signal should have the voltage range of 0-3.3V since anything out of this range is dangerous to msp430. Now the input is sampled at a high frequency using the built in ADC of MSP430G2231. The digital data output is of 10-bit length and is right shifted twice to downscale into an 8-bit data.

This 8-bit data is packetized and sent to the serial port using GPIO pin P1.0. Since MSP430G2231 doesn't have hardware UART, software UART is implemented using bit-banging.An alternative way would be using higher series of msp430 like MSP430G2553 which has built in UART.

This data is received by host side GUI application written in MATLAB and the graph is plotted in real time. The following is a snapshot of a 90% duty cycle waveform generated from another micrcontroller which is received by the oscilloscope circuit and is plotted in PC by MATLAB.

We can choose the COM port number to which the serial port is connected. Start button will initiate the data reception sequence from MSP430G2231. RMS voltage is computed from 100 data samples received and is displayed along with the waveform.

Comments

Shell Scripting to Display Bar Graphs in Linux Terminal

This week was quite hectic for me with course assignments and their merciless deadlines. One such assignment in Advanced Computer Architecture was simulation of various benchmarks in alpha architecture in simplescalar , a well-known computer architecture simulator. I was supposed to run a total of 4 benchmarks with different configurations of cache memory, instruction issue widths, commit widths, in-order execution modes, etc and I had to plot the required performance parameters for every benchmark. A conservative estimate would be around 40 plots! Since the simulation platform was Linux, I could breathe a sigh of relief since most things can be automated using a powerful tool called shell. Scripting made my life easier here since I can automate a bunch of simulations without having to keep an eye on each and every simulation which would take anywhere from 20 minutes to 20 hours. The problem arose when it came to plotting the performance results. Because, each simulation

Programming STM32 ARM microcontrollers in Arch Linux

Once upon a time, not so long ago, the 8-bit microcontrollers were ruling the hobbyist embedded world. But today, the 32-bit ARM Cortex Microcontrollers are so inexpensive and power efficient that there is no good reason to ignore them. Here, let us see how to program a STM32 ARM cortex Microcontroller in Linux environment. The specific microcontroller used here is an STM32F103C8 (ARM cortex M3) programmed in Arch linux. Components Generic STM32F103 board (blue pill) STLINK-V2 (STM32 programmer) Female-Female connectors All the above components can be bought from ebay for less than $10 total. The STLINK-V2 is optional since you can use any of USB-SERIAL converters like FT232, CP2102, PL2303, CH340 and the built-in UART bootloader of STM32 chip to program. So if you already have any of the above serial converters, you don't really need STLINK to program the STM32F103 microcontroller. But STLINK helps if you plan to use in circuit debugging functionalities. Software The

JTAG - Test Access Port (TAP)Controller based Xilinx FPGA configuration using Raspberry Pi

JTAG - Joint Test Action Group is an IEEE 1149.1 standard used in many silicon devices for programming and debugging purposes. Xilinx FPGAs support this JTAG protocol for their configuration. Here I have designed a JTAG FPGA bitstream programmer using Raspberry Pi which programs the bit file into FPGA in fraction of seconds! JTAG physical bus has four lines: TMS (Test Mode Select) TDI (Test Data In) TDO (Test Data Out) TCK (Test Clock) Components Used: Raspberry-Pi Xilinx Spartan 3E FPGA (XC3S250E in Papilio One) Jumper wires BLOCK DIAGRAM: TAP CONTROLLER: The TAP(Test Access Port) controller is a state machine inside the FPGA which changes it's state based on TMS input. For instance, let us assume that the state machine is in " Test-Logic-Reset " state. Now if I drive the TMS pin low and toggle the TCK pin, the state machine will go to " Run-Test/ Idle " state. This is how we move to different states. Note

Electronics Adventures

Search This Blog